# Reset due to error setting transmit frequency

**URL:** <https://community.cambiumnetworks.com/t/reset-due-to-error-setting-transmit-frequency/41134>\
**Category:** PMP\
**Created:** [July 16, 2015, 7:59am UTC](https://community.cambiumnetworks.com/t/reset-due-to-error-setting-transmit-frequency/41134 "2015-07-16T07:59:34Z")\
**Posts on this page:** 3\
**Page:** 1

<div class="post-metadata">

**Author:** ![MW\_WISP](https://d10gw3vjmzyp8.cloudfront.net/user_avatar/community.cambiumnetworks.com/mw_wisp/32/12227_2.png) [@MW\_WISP](https://community.cambiumnetworks.com/u/MW_WISP)\
**Post date:** [July 16, 2015, 7:59am UTC](https://community.cambiumnetworks.com/t/reset-due-to-error-setting-transmit-frequency/41134/1 "2015-07-16T07:59:34Z")

</div>

Hi,

I've 2 radio (PMP450 SM) with the following error message, both radios cannot register to APs:

```
System Reset Exception -- Watchdog Reset Cur ExtInt 0 Max ExtInt 0 Cur DecInt 0 Max DecInt 0 Cur Sync 0 Max Sync 0 Cur LED 2 Max LED 1 Cur WDOG 0 Max WDOG 1 Cur EthXcvr 0 Max EthXcvr 1 Cur FEC 0 Max FEC 0 Cur FPGA 0 Max FPGA 0 Cur FrmLoc 0 Max FrmLoc 0 Cur WatchDog 33 Max WatchDog 33 RTMLogStats 0 AAState 0 
Software Version : CANOPY 13.2.1 SM-DES
Board Type : P11
Device Setting : 5.4/5.7GHz MIMO OFDM - Subscriber Module - 0a-00-3e-b2-10-64
No valid accounts configured. Using default user account
FPGA Version : 081514
FPGA Features : DES, Sched;
01/07/2011 : 06:27:42 UTC : :Reset due to error setting transmit frequency 5512 at temperature 59 C
01/01/2011 : 00:00:00 UTC : :
01/01/2011 : 00:00:00 UTC : :Time Set
01/01/2011 : 00:00:00 UTC :
```

&nbsp;Is it an hardware failure?

---

<div class="post-metadata">

**Author:** ![CambiumMatt](https://d10gw3vjmzyp8.cloudfront.net/user_avatar/community.cambiumnetworks.com/cambiummatt/32/33533_2.png) [@CambiumMatt](https://community.cambiumnetworks.com/u/CambiumMatt)\
**Post date:** [July 17, 2015, 3:28pm UTC](https://community.cambiumnetworks.com/t/reset-due-to-error-setting-transmit-frequency/41134/2 "2015-07-17T15:28:17Z")

</div>

This can be an error that the radio will recover from with a reboot. &nbsp;We reduced the occurrence of this issue on R13.4, and would recommend updating to the latest software, which can be found&nbsp;[here](https://support.cambiumnetworks.com/files/pmp450/).

If this occurs repeatedly on these particular SMs (after several reboot cycles), then it's likely faulty hardware, and you can open a RMA case with the support team to get the radios replaced under warranty (email: support@cambiumnetworks.com)

Hope this helps,

Matt

---

<div class="post-metadata">

**Author:** ![MW\_WISP](https://d10gw3vjmzyp8.cloudfront.net/user_avatar/community.cambiumnetworks.com/mw_wisp/32/12227_2.png) [@MW\_WISP](https://community.cambiumnetworks.com/u/MW_WISP)\
**Post date:** [July 20, 2015, 8:36am UTC](https://community.cambiumnetworks.com/t/reset-due-to-error-setting-transmit-frequency/41134/3 "2015-07-20T08:36:00Z")

</div>

Ok, I'll open an RMA case.

Thank you
