60 GHz cnWave-3714 |
All |
In the Onboard Controller network, when seed prefix was modified, the software upgrade of CNs failed. |
60 GHz cnWave-3710 |
All |
When the antenna alignment was complete, ignition of the link stayed disabled. This was observed, occasionally. |
60 GHz cnWave-3687 |
V2000 |
V2000 did not respond to IPv4 pings that were destined to it. |
60 GHz cnWave-3682 |
All |
Stale Layer 2 tunnels were observed on PoPs. |
60 GHz cnWave-3613 |
V3000 |
When multiple relay ports were enabled on a V3000 device, the management IPv4 of CNs was not accessible. |
60 GHz cnWave-3530 |
All |
E2E controllerβs memory consumption increases over time. |
60 GHz cnWave-2360 |
V3000 and V5000 |
When the SFP module was present and the SFP link was not used, the device rebooted periodically. |
60 GHz cnWave-2850 |
All |
The E2E Controller device crashed while deleting a node. |
60 GHz cnWave-3162 |
All |
The UI did not support or enable ignition ever after the antenna alignment was complete. |
60 GHz cnWave-3213 |
V3000 and V5000 |
When a node was left idle for few hours, the Management IP was not accessible while accessing the node through a main port. |
60 GHz cnWave-3276 |
V1000 |
The device type was shown as CN on enabling E2E Controller for V1000. |
60 GHz cnWave-3301 |
All |
Prevented packets from being leaked, indefinitely, when there was no link to an installed SFP. |
60 GHz cnWave-3322 |
V5000, V3000, and V2000 |
Minion continuously restarted when a V5000, V3000, or V2000 device was set to factory default and configured as DN using the local UI. |
60 GHz cnWave-3349 |
V5000 |
Toposcan stopped traffic on the neighbour V5000 sector. |
60 GHz cnWave-3409 |
V1000 |
The iPerf throughput for V1000 was low on running the iPerf tool from the device UI (Tools page). |
60 GHz cnWave-3423 |
All |
The WSEC PSK password did not allow or support the $ character. |
60 GHz cnWave-3427 |
All |
In Fig O topology deployments () with wsec enabled, one of the wireless links did not come up. |
60 GHz cnWave-3466 |
All |
Controller crashed when a non-existing node was deleted using API. |
60 GHz cnWave-3477 |
All |
The VLAN traffic was not found in the allowed list due to which it was not dropped. |
60 GHz cnWave-3487 |
V2000 |
The V2000 node rebooted while downloading the field diags. |
60 GHz cnWave-3502 |
All |
A momentary drop was observed (for 10-20 seconds) in the CN traffic when a new CN link was added to PoP. |
60 GHz cnWave-3505 |
All |
Configuration snapshots taken by E2E Controller filled the docker file system. |
60 GHz cnWave-3540 |
All |
With Onboard Controller, when a new pop was added from cnMaestro, both the PoPs were not in the same IPv6 subnet. |
60 GHz cnWave-3549 |
All |
During the heavy bidirectional UDP traffic, the onboard PoP was unresponsive. |
60 GHz cnWave-3550 |
All |
SNMPv2 MIB: The sysName OID has been corrected to use node name instead of node MAC. |
60 GHz cnWave-3605 |
V5000 |
For V5000, the EIRP values were incorrect when sector 1 was configured with channel 1 and sector 2 was configured with channel 4. |
60 GHz cnWave-3606 |
V2000 |
When a client roamed from one V2000 to the other V2000 in a PtP connection, the client experienced drop of packets up to 30s. |
60 GHz cnWave-3622 |
V5000 |
V5000 as a PoP did not onboard cnMaestro after it was upgraded. It got stuck at the time of reboot. |
60 GHz cnWave-3200 |
All |
Restarted the DHCPv6 relay on encountering errors while sending the uplink packets. |
60 GHz cnWave-3325 |
All |
Synchronized Link and Node reporting status, which stopped link up and node down reporting issues. |
60 GHz cnWave-3330 |
All |
Corrected sysDescr and sysObjectID SNMP OIDs. |
60 GHz cnWave-3334 |
All |
On adding the primary link (after deleting it), the backup link got disconnected and CN moved to the primary link. |
60 GHz cnWave-3344 |
All |
Added an event if Gateway was unreachable. |
60 GHz cnWave-3347 |
All |
All disabled links got enabled after the PoP rebooted. |
60 GHz cnWave-3136 |
V2000 |
With the Aux port negotiated to 2.5 Gbps, the Main port did not work at 1 Gbps for V2000. |
60 GHz cnWave-28605 |
All |
Sometimes, the external E2E Controller consumed high CPU and memory when it was upgraded to 1.2.2 release version. |
60 GHz cnWave-3272 |
All |
In some instances, CN lost WSEC configuration while scanning. |
60 GHz cnWave-3141 |
All |
Deleted the routes used by DHCPv6 relay when a CPE interface was down. This behaviour can be turned off by setting the CAMBIUM_DHCPv6_DELETE_ASSIGNMENTS_CPE_DOWN parameter to false. |
60 GHz cnWave-3152 |
All |
The UI did not display the drop-down list options for Select Logs and Select Nodes parameters (on the Engineering Logs page) when the browser was refreshed. |
60 GHz cnWave-3182 |
All |
Added timestamps to the DHCPv6 relay logs. |
60 GHz cnWave-3191 |
V2000 |
The Link Uptime statistics was incorrectly updated on the UI in case of a hard reboot of the PoP node. |
60 GHz cnWave-3200 |
All |
Added a restart mechanism to DHCPv6 Relay when it was unable to relay messages to the DHCPv6 server. |
60 GHz cnWave-3222 |
V2000 |
Factory reset did not disable E2E Controller. |
60 GHz cnWave-3245 |
All |
The UI allowed configuring special characters for the Max EIRP value on an individual node. |
60 GHz cnWave-3250 |
V2000 |
The V2000 throughput was lower in Layer 3 mode or when it was a DN in a mesh topology. |
60 GHz cnWave-3252 |
V2000 |
Sometimes, the Main port of V2000 did not pass traffic even if it was linked up at 1000M (on rare occasions).This event occurred following after a 10M link transition (UP and Down). |