New Power Supply Available for 450i

Products PMP
1

Cambium Networks now has available a lower priced option to power the PMP and PTP 450i radio products.

The N000000L034A is a 56 VDC, 30W power supply that will operate any of the 450i radio equipment in standalone mode (i.e. not being powered by CMM).  Note that this PSU requires an IEC60320 Type C5 AC Line cord, part numbers are listed below. These are the same line cords that are used with the N000900L001A, and are not new parts.

This supply can be used instead of N000065L001B, provided you’re not planning to use the AUX port with a device that may exceed 10 Watts.

Pictures:

N000000L034A_AC_side_sm.jpg

N000000L034A_RJ-45_side_sm.jpg
N000000L034A_RJ-45_side_sm.jpg712×568 230 KB
IEC60320_C5_connector.jpg

Part Number

Description

MSRP (USD)

N000000L034A

POWER SUPPLY, 30W, 56V - Gbps support

$25

Optional AC Line Cords

N000900L007A

CABLE, UL POWER SUPPLY CORD SET, US

$5

N000900L008A

CABLE, UL POWER SUPPLY CORD SET, EU

$5

N000900L009A

CABLE, UL POWER SUPPLY CORD SET, UK

$5

Below is the list of compatible parts (450i platform parts):

Part Number

Description
   

C009045A001A

900 MHz PMP 450i Connectorized Access Point

C050045A001A

5 GHz PMP 450i Connectorized Access Point (ROW)

C050045A002A

5 GHz PMP 450i Connectorized Access Point (FCC)

C050045A003A

5 GHz PMP 450i Connectorized Access Point (EU)

C050045A004A

5 GHz PMP 450i Connectorized Access Point (DES Only)

C050045A005A

5 GHz PMP 450i Integrated Access Point, 90 degree (ROW)

C050045A006A

5 GHz PMP 450i Integrated Access Point, 90 degree (FCC)

C050045A007A

5 GHz PMP 450i Integrated Access Point, 90 degree (EU)

C050045A008A

5 GHz PMP 450i Integrated Access Point, 90 degree (DES Only)

C050045A015A

5 GHz PMP 450i Connectorized Access Point (IC)

C050045A016A

5 GHz PMP 450i Integrated Access Point, 90 degree (IC)

C050045C001A

5 GHz PMP 450i Connectorized Subscriber Module

C050045C002A

5 GHz PMP 450i SM, Integrated High Gain Antenna

C050045B001A

5 GHz PTP 450i END, Connectorized (ROW)

C050045B002A

5 GHz PTP 450i END, Integrated High Gain Antenna (ROW)

C050045B003A

5 GHz PTP 450i END, Connectorized (FCC)

C050045B004A

5 GHz PTP 450i END, Integrated High Gain Antenna (FCC)

C050045B005A

5 GHz PTP 450i END, Connectorized (EU)

C050045B006A

5 GHz PTP 450i END, Integrated High Gain Antenna (EU)

C050045B007A

5 GHz PTP 450i END, Connectorized (DES Only)

C050045B008A

5 GHz PTP 450i END, Integrated High Gain Antenna (DES only)

C050045B015A

5 GHz PTP 450i END, Connectorized (IC)

C050045B016A

5 GHz PTP 450i END, Integrated High Gain Antenna (IC)

If there are any questions or comments, feel free to post them below.

Thanks,

Matt

1 Like
2

Thats a gigabit PSU right?

3
@leisser wrote:

Thats a gigabit PSU right?

Yes.

4

I would argue this is the perfect timing for an errata on the Epmp integrated CPE's with "22-56v" labeling, but that will blow at 34v.  

it's a matter of time before someone makes an incorrect swap, and altough it will not harm the GPS units, connectorized and integrated (10/100) units will not like this psu.

Also about the force200/180 with gigabit bricks, i have a feeling this gigabit brick and those gigabit bricks are not interchangeable.

1 Like
5

Quick question because I have been given different answers.  Is this the power supply we would use for the two 450i-900 AP's with a UGPS configuration.  I was given the part number N000065L001B with a figure 8 line cord as what I needed for the UGPS implementation.  

Thanks!

PS I am not a power expert just the person who places the orders.