User Defined Overrides

Products cnMaestro
1

Hi 

Is there a proper list of all User Defined Override settings and the corresponding gui fields in the CNPilot R series routers?

I specifically want to disable the https web interface and switch back to http but I would prefer if there was a full list showing every setting and the acceptable options

2

Hello,

As far as I'm aware, we don't have a document that goes over all the configuration file settings for cnPilot Home devices.  We do have a Knowledge Base article that contains a procedure for setting up your own User-Defined Overrides and finding the correct settings.

https://community.cambiumnetworks.com/t5/cnMaestro/Unique-per-device-values-in-AP-Groups-using-User-defined/m-p/63560

Please post here if you have any questions or issues.

I have also forwarded this post to our device team to double check if the documentation you've requested is available.

3

After speaking with the device team the closest we have today is the below Knowledge Base article.  It does include the web interface settings for http/https.

http://community.cambiumnetworks.com/t5/cnPilot-R-Series-Home-Small/cnPilot-R-series-Home-Routers-Important-Configuration-Parameters/m-p/91640#M35

4

Thanks 

Please add the following to the knowledgebase article

Host name of the device (eg. for filesharing) 
HostName=cnPilot-R200


LAN Settings
lan_ipaddr=192.168.11.1
lan_netmask=255.255.255.0
dhcpEnabled=0   (0=off 1=on)
dhcpStart=192.168.11.2
dhcpEnd=192.168.11.254
dhcpMask=255.255.255.0
dhcpPriDns=192.168.11.1
dhcpSecDns=8.8.8.8
dhcpGateway=192.168.11.1
dhcpLease=86400


DMZ

DMZEnable=0 (0=off 1=on)
DMZAddress=

NTP
NTPEnable=1 (1=on 0=off)
NTPServerIP=pool.ntp.org
SecondNTPServerIP=
NTPSync=60
NTPRetryTimes=3


Dynamic DNS
DDNSProvider=     (name of provider, variables unknown yet) 
DDNS=    (ddns address or hostname) 
DDNSAccount=   (username)
DDNSPassword=    (password)
WatchDogEnable=1

Wifi
SSID1=CambiumSSID
Channel=1         (1-11)
TxPower=100    (percentage)
WPAPSK1=12345678

Telnet
RemoteTelnet=0    (access via telnet from wan 0=block 1=allow)
LocalTelnet=0      (access via telnet from lan 0=block 1=allow)
TelnetPort=23
telnet_allow_ip=0.0.0.0    (0.0.0.0 = allow all) 

1 Like
5

2.4ghz More settings:

HT_BW=1     (2.4ghz 0=20mhz mode 1=20/40mhz mode)
AutoChannelSelect= (0=use specific channel 1=Auto)
Channel= (1-13)

5ghz more settings:
RTDEV_HT_BW=  (0=20mhz 1=20/40mhz)
RTDEV_VHT_BW= (0=20/40mhz 1=80mhz)
RTDEV_AutoChannelSelect= (0=use specific channel 1=Auto)
RTDEV_Channel= (5ghz channel number)

1 Like
6

Hi Ray,

I've added your posts to the knowledge base article.  Thank you for gathering and organizing this information.  Are you able to post replies to the article?

7

No there is no reply option to the article

1 Like